IEEE-488
维库，知识与思想的自由文库
5个分类: 需要翻譯的文章 | 翻譯請求 | CBM storage devices | Computer buses | 来自中文维基百科
IEEE-488正在翻译。欢迎您积极翻译与修订。
目前已翻译0%，原文在http://en.wikipedia.org/wiki/IEEE-488。
| IEEE-488 / HP-IB / GPIB | ||
|---|---|---|
|
|
||
| 類別 | General purpose data bus | |
| 產品歷史 | ||
| 設計者 | Hewlett-Packard | |
| 設計年代 | late 1960s standardized in 1975 | |
| 製造商 | Hewlett-Packard | |
| 製造年代 | 1960s to present | |
| 規格 | ||
| 外接 | yes | |
| 資料訊號 | Parallel data bus with handshaking | |
| 位元寬度 | 8 bits | |
| 資料頻寬 | 8 Mbit/s (later extended to 64 Mbit/s) |
|
| 最大裝置數量 | 15 | |
| 協定 | Parallel | |
| 纜線 | 20 meters max | |
| 腳位數量 | 24 (8 data, 5 bus management, 3 handshake, 8 ground) | |
| 連接器 | 24-pin Amphenol-designed micro ribbon | |
| 腳位配置 | ||
 A female IEEE-488 connector |
||
| Pin 1 | DIO1 | Data input/output bit. |
| Pin 2 | DIO2 | Data input/output bit. |
| Pin 3 | DIO3 | Data input/output bit. |
| Pin 4 | DIO4 | Data input/output bit. |
| Pin 5 | EOI | End-or-identify. |
| Pin 6 | DAV | Data valid. |
| Pin 7 | NRFD | Not ready for data. |
| Pin 8 | NDAC | Not data accepted. |
| Pin 9 | IFC | Interface clear. |
| Pin 10 | SRQ | Service request. |
| Pin 11 | ATN | Attention. |
| Pin 12 | SHIELD | |
| Pin 13 | DIO5 | Data input/output bit. |
| Pin 14 | DIO6 | Data input/output bit. |
| Pin 15 | DIO7 | Data input/output bit. |
| Pin 16 | DIO8 | Data input/output bit. |
| Pin 17 | REN | Remote enable. |
| Pin 18 | GND | (wire twisted with DAV) |
| Pin 19 | GND | (wire twisted with NRFD) |
| Pin 20 | GND | (wire twisted with NDAC) |
| Pin 21 | GND | (wire twisted with IFC) |
| Pin 22 | GND | (wire twisted with SRQ) |
| Pin 23 | GND | (wire twisted with ATN) |
| Pin 24 | Logic ground | |
IEEE-488 is a short-range, digital communications bus specification. It was originally created for use with automated test equipment, and is still in wide use for that purpose. IEEE-488 is also commonly known as HP-IB (Hewlett-Packard Instrument Bus) and GPIB (General Purpose Interface Bus).
IEEE-488 allows up to 15 devices to share a single 8-bit parallel electrical bus by daisy chaining connections. The slowest device participates in control and data transfer handshakes to determine the speed of the transaction. The maximum data rate is about one MB/s in the original standard, and about 8 MB/s with IEEE-488.
The IEEE-488 bus employs 16 signal lines — eight bi-directional used for data transfer, three for handshake, and five for bus management — plus eight ground return lines.
目录 |
[编辑] 歷史
In the late 1960s, Hewlett-Packard (HP) [now known as Agilent Technologies] was a manufacturer of test and measurement instruments, such as digital multimeters and logic analyzers. HP developed the HP Interface Bus (HP-IB) to enable easier interconnection between instruments and controllers such as computers. The bus was relatively easy to implement using the technology at the time, using a simple parallel electrical bus and several individual control lines.
Other manufacturers copied HP-IB, calling their implementation the General Purpose Interface Bus (GPIB).
In 1975 the bus was standardized by the Institute of Electrical and Electronics Engineers as the IEEE Standard Digital Interface for Programmable Instrumentation, IEEE-488-1975 (now 488.1). IEEE-488.1 formalized the mechanical, electrical, and basic protocol parameters of GPIB, but said nothing about the format of commands or data. The IEEE-488.2 standard, Codes, Formats, Protocols, and Common Commands for IEEE-488.1 (June 1987), provided for basic syntax and format conventions, as well as device-independent commands, data structures, error protocols, and the like. IEEE-488.2 built on -488.1 without superceeding it; equipment can conform to -488.1 without following -488.2.
While IEEE-488.1 defined the hardware, and IEEE-488.2 defined the syntax, there was still no standard for instrument-specific commands. Commands to control the same class of instrument (e.g., multimeters) would vary between manufacturers and even models. A standard for device commands, SCPI, was introduced in the 1990s. Due to the late introduction, it has not been universally implemented.
National Instruments introduced a backwards-compatible extension to IEEE-488.1, originally known as HS-488. It increased the maximum data rate to 8 MB/s, although the rate decreases as more devices are connected to the bus. This was incorporated into the standard in 2003, as IEEE-488.1-2003.
In addition to the IEEE, several other standards committees have adopted HP-IB. The American National Standards Institute's corresponding standard is known as ANSI Standard MC 1.1, and the International Electrotechnical Commission has its IEC Publication 625-1.
[编辑] 應用
At the outset, HP-IB's designers did not specifically plan for IEEE-488 to be a standard peripheral interface for general-purpose computers. By 1977 the Commodore PET/CBM range of educational/home/personal computers connected their disk drives, printers, modems, etc, by IEEE-488 bus. All of Commodore's post-PET/CBM 8-bit machines, from the VIC-20 to the C128, utilized a proprietary 'serial IEEE-488' for peripherals, with round DIN connectors instead of the heavy-duty HP-IB plugs or a card-edge connector plugging into the motherboard (for PET computers).
Hewlett-Packard and Tektronix also used IEEE-488 as a peripheral interface to connect disk drives, tape drives, printers, plotters etc. to their workstation products and HP's HP 3000 minicomputers. While the bus speed was increased to 10 MB/s for such applications, the lack of command protocol standards limited third-party offerings and interoperability, and later, faster, open standards such as SCSI eventually superseded IEEE-488 for peripheral access.
Additionally, some of HP's advanced pocket calculators/computers of the 1980s, such as the HP-41 and HP-71 series, could work with various instrumentation via an optional HP-IB interface. The interface would connect to the calculator via an optional HP-IL module.
[编辑] 訊號列表
| bus line | description |
| DIO1–DIO8 | Data input/output bits. These 8 lines are used to read and write the 8 bits of a data or command byte that is being sent over the bus. |
| NRFD | Not ready for data. NRFD is a handshaking line asserted by listeners to indicate they are not ready to receive a new data byte. |
| DAV | Data valid. This is a handshaking line, used to signal that the value being sent with DIO1-DIO8 is valid. During transfers the DIO1-DIO8 lines are set, then the DAV line is asserted after a delay called the 'T1 delay'. The T1 delay lets the data lines settle to stable values before they are read. |
| NDAC | Not data accepted. NDAC is a handshaking line asserted by listeners to indicate they have not yet read the byte contained on the DIO lines. |
| ATN | Attention. ATN is asserted to indicate that the DIO lines contain a command byte (as opposed to a data byte). Also, it is asserted with EOI when conducting parallel polls. |
| EOI | End-or-identify. This line is asserted with the last byte of data during a write, to indicate the end of the message. It can also be asserted along with the ATN line to conduct a parallel poll. |
| IFC | Interface clear. The system controller can assert this line (it should be asserted for at least 100 microseconds) to reset the bus and make itself controller-in-charge. |
| REN | Remote enable. Asserted by the system controller, it enables devices to enter remote mode. When REN is asserted, a device will enter remote mode when it is addressed by the controller. When REN is false, all devices will immediately return to local mode. |
| SRQ | Service request. Devices on the bus can assert this line to request service from the controller-in-charge. The controller can then poll the devices until it finds the device requesting service, and perform whatever action is necessary. |
[编辑] 連接頭
[编辑] IEEE-488
IEEE-488 uses 24-pin Amphenol-designed micro ribbon connectors (often incorrectly termed Centronics-type), most commonly in a stackable male/female combination that allows for easy daisy-chaining by stacking cables. Mechanical considerations limit the number of stacked connectors to four or less. They are held in place by screws, which come in UTS (now largely obsolete) or metric (M3.5×0.6) threads. By convention, metric screws are colored black, as the two threads do not mate. Total cable length is limited to 20 metres, although non-standard "bus extender" devices are available.
[编辑] IEC-625
The IEC-625 standard prescribes the use of 25-pin D-subminiature connectors (the same are used for parallel ports on PCs). This standard did not gain significant market acceptance against the established 24-pin connector.
[编辑] See also
[编辑] External links
- IEEE Standards
- A GPIB tutorial (mirror) from TransEra Corporation
- Tutorials, application notes, and sample programs from ICS Electronics (index is HTML; content is PDF)
- Linux GPIB drivers and libraries
- KE5FX GPIB Toolkit, several freeware GPIB applications for Windows
- From http://www.bitsavers.org:
- Python Wrapper for NI GPIB
| 本文參考了依GFDL授權發佈的「FOLDOC」。 This article was originally based on material from the Free On-line Dictionary of Computing and is used under the GFDL. |
